| 引用本文： |
-
闫朝辉,侯治龙,文伟,刘志宏,吴杰峰,朱自安,韦俊.μ子源超导俘获线圈测试杜瓦设计与校核[J].低温物理学报,2020,(6):285-291. [点击复制]
- YAN Zhaohui,HOU Zhilong,WEN Wei,LIU Zhihong,WU Jiefeng,ZHU Zian,WEI Jun.Design and Verification of Muon Source Superconducting Capture Magnet Test Dewar[J].LOW TEMPERATURE PHYSICAL LETTERS,2020,(6):285-291. [点击复制]
|
|
| |
|
|
| 本文已被：浏览 1124次 下载 5668次 |
码上扫一扫！ |
| μ子源超导俘获线圈测试杜瓦设计与校核 |
|
闫朝辉1,2, 侯治龙3,4, 文伟1, 刘志宏1, 吴杰峰1, 朱自安3,4, 韦俊1,5
|
|
|
| (1.中国科学院合肥物质科学研究院等离子体物理研究所,合肥230031;2.中国科学技术大学,合肥230026;3.中国科学院高能物理研究所,北京100049;4.中国科学院大学,北京100049;5.合肥聚能电物理高技术开发有限公司,合肥230031) |
|
| 摘要: |
| 根据高μ子源超导俘获线圈整体测试系统的要求,设计了μ子源超导俘获线圈测试杜瓦系统.包含液氦杜瓦、真空杜瓦及绝热冷屏,采用Solidworks软件对测试杜瓦系统进行3D建模.通过对绝热冷屏统进行了详细的传热学计算,绝热冷屏的可以满足μ子源超导俘获线圈测试过程的漏热需求;根据μ子源超导俘获线圈测试实际工况,对真空杜瓦和液氦杜瓦进行了Ansys有限元软件分析与校核,得到杜瓦详细的应力及变形结果,分析表明,测试杜瓦的设计较为合理,可以作为工程设计的理论计算依据 |
| 关键词: μ子源,俘获线圈,测试杜瓦,校核 |
| DOI： |
|
| 基金项目: |
|
| Design and Verification of Muon Source Superconducting Capture Magnet Test Dewar |
|
YAN Zhaohui1,2, HOU Zhilong3,4, WEN Wei1, LIU Zhihong1, WU Jiefeng1, ZHU Zian3,4, WEI Jun1,5
|
| (1.Institute of Plasma Physics, Hefei Institutes of Physical Science, Chinese Academy of Sciences, Hefei 230031;2.University of Science and Technology of China,Hefei 230031;3.Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049;4.University of Chinese Academy of Sciences, Beijing 100049;5.Hefei Juneng, Electrophysics High Technology Development Co., Ltd Hefei 230031) |
| Abstract: |
| According to the source of high muon captured by the superconducting coil overall requirements of the testing system, designed the muon source captured by the superconducting coil test dewar system, contains the liquid helium dewar, vacuum dewar and adiabatic theater, the adiabatic theater system carried on the detailed heat transfer calculation, adiabatic theater can satisfy muon source captured by the superconducting coil heat leakage testing requirements : According to the actual conditions of the muon source superconducting capture coil test , the vacuum dewar and liquid helium dewar were analyzed and checked by ANSYS finite element software, and the detailed stress and deformation results of the dewar were obtained. The analysis shows that the design of the test dewar is reasonable and can be used as the theoretical calculation basis for engineering design. |
| Key words: Muonsource,Capturecoil,Testdewar,Check |
|
|
|
|
|